Home › Blog › OpenView

OpenView Installer or DIY: Can You Set Up the Dish Yourself?

OpenViewBy our Hout Bay DStv teamUpdated 19 October 20267 min read

Can you skip the OpenView installer and put the dish up yourself? Some people can, especially if a dish is already on the wall. In Hout Bay, though, steep slopes, Atlantic wind and mountain shadow make the full job harder than the box suggests. Here's an honest split between what you can do and what's worth paying for.

Quick answer

Yes, you can set up OpenView yourself if a working dish with a clear view is already in place. Plug in the decoder, run the channel scan and activate it online. Mounting a new dish, working at height and fine alignment are where an OpenView installer earns their fee, especially on windy, sloped Hout Bay plots.

What DIY OpenView actually involves

A full setup has four parts. Only some of them are friendly to do yourself.

  1. Fix a bracket and an 80 to 85cm dish somewhere with a clear north-east view.
  2. Fit the LNB and run coaxial cable to the TV, sealing every outdoor connector.
  3. Aim the dish at the Intelsat 20 satellite at 68.5 degrees East and lock it in place.
  4. Connect the decoder, scan channels and activate the box.

Steps one to three happen outside and often up high. Step four happens on your couch.

As DStv installers in Hout Bay, we see plenty of half-finished DIY jobs. The indoor part almost always went fine. It's the outdoor work, done on a calm afternoon, that comes undone in the first proper blow.

Tools a full DIY job needs

Mounting a dish properly takes a hammer drill, masonry bits, the right wall plugs for your brick or plaster, a compass, a spanner set, cable clips and weatherproof tape or boots. Most people own only half of that list, so the hidden shopping trip adds to the cost.

DIY or OpenView installer: task by task

TaskFine to DIY?Why
Plugging in the decoder and TVYesIndoor, low risk, the manual covers it
Activating the boxYesDone online, on WhatsApp or in the OpenView app
Rescanning channelsYesA simple menu option
Reusing an existing dishSometimesOnly if the LNB and cable are sound
Mounting a new dishBest left to a proHeight, wall fixings and wind loading
Fine alignmentBest left to a proNeeds a signal meter, not just an app

The safe DIY route: reusing an existing dish

Lots of Hout Bay homes already have a DStv dish, even rentals and holiday homes. OpenView uses the same satellite position, so that dish can often feed an OpenView decoder. If it's in good shape, the whole job can be done indoors.

  1. Find the cable that runs from the dish to the TV room and check the plug end isn't green or crusty.
  2. Screw the cable into the decoder's LNB input by hand. Don't overtighten.
  3. Connect the decoder to the TV with an HDMI cable and switch both on.
  4. Follow the on-screen setup and run a channel scan.
  5. Activate the decoder on openview.co.za, WhatsApp or the app using the box's details.

Our OpenView activation steps walk through that last part in more detail.

Safety first

Don't climb onto the roof or lean off a ladder to check or turn a dish. Many Hout Bay houses sit on steep slopes, and a gust off the Atlantic can catch a dish like a sail. Keep DIY to the ground and indoors, and never touch wiring near mains power.

Need DStv installers in Hout Bay?

Tell us what you need or what your screen is showing. We give you a clear price before we drive out.

Why an OpenView installer is worth it in Hout Bay

Hout Bay is a tough place to put up a dish. Chapman's Peak and the Karbonkelberg throw long shadows across parts of the valley, and the satellite sits fairly high in the north-east sky. Moving the dish a metre can be the difference between full signal and none.

Wind is the next problem. A dish that's tight on a calm day can drift in a strong blow if the bracket or wall plugs aren't right for the load. Then the picture freezes and you're back on the phone.

Salt air on the connectors

Near the beach, in Llandudno and on Victoria Road, salt gets into every unsealed connector. A DIY job with bare fittings may work for a few months, then fade. We use weatherproofing that's made for the coast. Our post on salt, wind and signal faults shows what that damage looks like.

Alignment needs a meter

A phone app gets you close. Our signal finder comparison explains why a proper meter does the fine-tuning. The extra margin helps the dish ride out rain fade in winter.

OpenView installation price vs the DIY bill

DIY isn't free either. You still buy the decoder, a dish kit, a bracket, cable and connectors, and you might need a drill and long bit. At the time of writing, the OpenView decoder is ZAR 799 on openview.co.za, with retail specials from around R599.

A decoder with a dish and installation voucher is around R1,699. A local OpenView installer usually quotes a standard job from around R850 to R1,400, plus the decoder. Steep sites in Hughenden or Scott Estate may cost more. Ask our team for a current quote.

If a DIY dish ends up misaligned, paying for satellite dish alignment afterwards can wipe out the saving.

Signs it's time to call an OpenView installer

  • No dish on the house, or the old one is rusted or bent.
  • The only clear view is from the roof or a high wall.
  • Your channel scan finds nothing, even after checking the cable.
  • The signal drops every time the wind picks up.
  • You want OpenView on a second TV in another room.

For holiday homes in Penzance Estate that stand empty for weeks, a proper install also means fewer surprises when guests arrive. If you're moving an old dish to a new spot, our relocations and reconnections team can handle it.

Get help from an OpenView installer in Hout Bay

Done what you safely can and still stuck? We'll pick up from there. Our OpenView installation service covers mounting, alignment, cabling and activation, and we quote before we drive out. If this doesn't fix it, call a technician on 072 237 6363 or send us a message.

OpenView installer: FAQs

Can I install OpenView myself instead of using an installer?

Yes, if a sound dish with a clear view is already on the house. You connect the decoder, scan channels and activate it online. Mounting a new dish and fine alignment are safer and more reliable with an installer.

How much does an OpenView installer charge?

At the time of writing, a standard install by a local team usually starts from around R850 to R1,400, plus the decoder. Steep or windy sites may cost more. Ask our team for a current quote for your home.

Does OpenView need a dish?

Yes. OpenView is a satellite service, so it needs a dish of around 80 to 85cm pointed at the right satellite. An existing DStv dish can often be reused once the LNB and cable are checked.

Can I align an OpenView dish with a phone app?

A satellite finder app helps you point the dish roughly in the right direction. For a strong, stable picture, fine alignment needs a proper signal meter, which installers carry.

Is DIY OpenView a good idea for a Hout Bay holiday home?

Only if the dish is already in place and sound. Salt air and strong wind are hard on DIY fittings, and nobody is there to notice a fault midweek. A proper install with sealed connectors usually saves call-outs later.

Talk to our Hout Bay team

Call or WhatsApp us for a quote. We answer quickly and we always price the job before we arrive.