Home › Blog › Decoders and Equipment

What You Need to Connect DStv Explora to WiFi at Home

Decoders and EquipmentBy our Hout Bay DStv teamUpdated 24 October 20267 min read

To connect DStv Explora to WiFi you need three things: a working router with an uncapped line, the right link for your model of Explora, and a few minutes with the remote. That's the whole shopping list. Below we explain each piece, so you can check what's already in your Hout Bay home before you buy anything.

Quick answer

An Explora Ultra has WiFi built in, so you only need your router name and password. Older Explora boxes need a DStv WiFi Connector or a network cable from the router. DStv recommends an uncapped line of at least 2Mbps for downloads. Once that's sorted, you can connect your DStv Explora to WiFi in about ten minutes.

Your kit list to connect DStv Explora to WiFi

Most homes already have half of this. Tick off what you've got, then you'll know what's missing.

  • An Explora that already shows satellite channels on the TV.
  • A router that's switched on and gives internet to your phone.
  • The router's network name and password, written down.
  • For older boxes: a DStv WiFi Connector, or a network cable long enough to reach the router.
  • The Explora remote, with fresh batteries.
  • An uncapped fibre or wireless internet package.

If the decoder itself isn't installed yet, start with our Explora installation team. The internet side only makes sense once the dish and Smart LNB are feeding the box properly.

Which DStv Explora do you have, and how will it connect to WiFi?

The model decides what you buy. Look at the label on the back or underside of the decoder, or check the MyDStv app.

Your decoderWiFi inside?What you need to addRough effort
Explora UltraYesNothing, just the passwordA few minutes in settings
Explora 3A or 3BNoWiFi Connector or a network cablePlug in and follow the prompts
Older first and second modelsNoWiFi Connector or a network cablePlug in and follow the prompts

Thinking of swapping an old box for an Ultra anyway? Our comparison of Explora versus Explora Ultra prices helps you weigh it up.

The internet line behind the router

DStv's published guide asks for at least 2Mbps for downloads and remote recording, 4Mbps for SD streaming and 10Mbps for HD. Most fibre lines in Hout Bay clear that easily. Some LTE and fixed wireless packages in the hillier parts of the valley can struggle at night.

Data is the other half. DStv recommends an uncapped account because downloading shows eats a lot of it. A small capped bundle on a holiday house router can run dry in a weekend of Catch Up.

Good to know

Your normal satellite channels come off the dish, not the internet. If the WiFi drops, live TV keeps playing. You only lose the online extras like Catch Up until the link is back.

The DStv WiFi connector for Explora models without WiFi

The connector is a small adapter that gives older Explora boxes a wireless link. It powers off a USB port on the back of the decoder, so you don't need a spare wall plug.

If your router has a WPS button

DStv describes a quick pairing method. Plug the connector into the Explora, wait for its light to settle, press WPS on the router and follow the prompts on screen.

If there's no WPS button

Use the docking station that comes with it. The set-up screen opens, you pick your network from the list and type the password using the remote.

Need DStv installers in Hout Bay?

Tell us what you need or what your screen is showing. We give you a clear price before we drive out.

When a cable beats wireless

If the router sits in the same room as the TV, a network cable is DStv's steadiest option. There's nothing to pair and nothing for neighbours' networks to interfere with. Our article on the WiFi Connector versus a LAN cable goes deeper into that choice.

Cables also help in split-level homes, which Hout Bay has plenty of. A house stepped down a slope in Hughenden or Penzance Estate often has the router upstairs and the lounge two levels below. WiFi fades fast through concrete slabs, so a neat cable or a mesh point fixes it for good.

Hout Bay homes: what slows the job down

Most snags we see here aren't technical. They come from the way homes are used in the valley.

  • Holiday homes and rentals: in Llandudno and Northshore the router is often switched off between guests, so the decoder can't find the network when people arrive.
  • New internet provider: a router swap brings a new network name and password, and the Explora has to be joined again.
  • Thick walls: older stone houses near Victoria Road soak up signal between rooms.
  • Salt air outdoors: if a cable runs outside to a cottage, cheap connectors corrode, so we use sealed fittings.

Weak WiFi across the house is a router problem, not a decoder one. Our WiFi and network installation service can sort coverage for the TV and the rest of the house at once.

Connect DStv Explora to TV first, then to WiFi

People sometimes ask how to connect DStv Explora to TV and WiFi in one go. Do it in order. Run an HDMI cable from the decoder to the TV and get a clear picture on satellite channels before you touch the network settings.

Our guide to every DStv cable and port shows where each lead goes if the back of the box looks confusing.

Technician tip

Once you're online, press the DStv button, go to Help, then Tools, then Connectivity Checker. Two green ticks, one for the router and one for the internet, mean you're done. A cross on the first means the decoder can't see the router at all.

Get the job done properly in Hout Bay

If you'd rather not fiddle, our technicians can bring the right connector or cable and connect DStv Explora to WiFi while they're on site. We check the Connectivity Checker with you before we leave. Call or WhatsApp 072 237 6363, or book our DStv installers in Hout Bay through the contact page.

Connect DStv Explora to WiFi: FAQs

Can DStv Explora connect to WiFi without a connector?

Only the Explora Ultra can, because it has WiFi built in. The 3A, 3B and older models need either the DStv WiFi Connector or a network cable running straight from the router. Check the label on your decoder before you buy anything.

How do you connect DStv Explora to WiFi router with no WPS button?

Use the docking station that comes with the WiFi Connector. Slot the connector in, plug the dock into a USB port on the back of the Explora and the set-up screen opens. Choose your network and type the password with the remote.

Do I need fibre to connect my Explora to the internet?

Not always. DStv asks for at least 2Mbps for downloads and 10Mbps for HD streaming, plus an uncapped package. Fibre is the easiest way to meet that, but a strong fixed wireless or LTE line can work if it isn't capped.

Can you help connect an Explora in a Hout Bay holiday home?

Yes. We often set up decoders in rentals and holiday houses around Hout Bay and Llandudno. We'll connect the Explora to the router, run the Connectivity Checker and show the owner what to switch on when guests arrive.

Will my DStv still work if the WiFi goes down?

Yes. Live channels come from the satellite dish, so they keep playing without internet. You'll only lose online features such as Catch Up until the router is back online.

Talk to our Hout Bay team

Call or WhatsApp us for a quote. We answer quickly and we always price the job before we arrive.