Home › Blog › Installation and Costs
TV Wall Mounting Mistakes That Damage Walls
A cracked patch of plaster, a ring of rust or a row of abandoned holes: walls tell you exactly how a screen was hung. The good news is that most TV wall mounting damage comes from a handful of avoidable mistakes. Here they are, with the fix for each, so your wall still looks good when the TV comes down one day.
Quick answer
The TV wall mounting mistakes that damage walls most are using the wrong plugs for the wall, hanging heavy arms on drywall without studs, drilling into hidden wiring or pipes, guessing the height and redrilling, and cheap fixings that rust near the sea. Check the wall, mark once, and match every fixing to the load.
Mistake 1: trusting the plugs in the box
Bracket kits come with a small bag of plastic plugs and screws. They're made to suit "most walls", which really means none in particular. In soft or old brick, those plugs spin, the hole widens, and the bracket slowly pulls away.
The fix is simple. Match the plug to the wall and the load: proper heavy-duty plugs for solid brick, sleeve anchors for concrete, chemical anchors for crumbly masonry. In many older Hout Bay homes near Victoria Road, the brick behind the plaster is softer than it looks. Our checklist for picking installers includes asking what fixings they use.
Mistake 2: full motion TV wall mounting on bare drywall
A full motion arm turns your TV into a lever. Pull the screen out and the force on the top fixings multiplies. On drywall alone, the board tears around the screws, leaving a hole far bigger than the bracket.
- Find the studs and bolt the bracket into them.
- If the studs are in the wrong place, add a timber backing board spanning two of them.
- For big screens on partitions, choose a fixed or tilt bracket instead of an arm.
Our post on tilt and swivel brackets covers when an arm is worth the extra strain on the wall.
Mistake 3: drilling blind near plugs and taps
This is the expensive one. A drill bit through a water pipe means a wet wall and a plumber. Through a live cable, it's a real danger. Wires usually run straight up or down from switches and plug points, and pipes follow the line to taps and geysers.
Safety first
Don't drill in line with plug points, switches or the plumbing on the other side of the wall. If you're not sure what's hidden there, stop. Anything involving mains power or work up a ladder is a job for a technician, not a weekend project.
Mistake 4: guessing the height for TV wall mounting
Hold the TV up, eyeball it, drill. Then sit down and realise it's far too high. Now there are four holes to fill and four more to make. Every redrill weakens the wall and leaves patches that show through paint.
Sort out how high to mount a TV before you touch the drill. Sit where you watch, mark eye level on masking tape, and line the centre of the screen up with it. Measure from the bracket holes to the screen's centre so the marks are right first time.
| Mistake | What the wall shows | How to avoid it |
|---|---|---|
| Wrong plugs | Cracks around a sagging bracket | Fixings matched to brick, concrete or drywall |
| Arm on bare drywall | Torn board, large hole | Bolt into studs or add a backing board |
| Drilling blind | Damp patch or tripped power | Avoid lines from plugs, switches and taps |
| Guessed height | Extra filled holes | Mark eye level and measure first |
| Cheap fixings near the sea | Rust streaks down the paint | Stainless or coated screws and brackets |
| Chasing cables carelessly | Cracked plaster lines | Trunking, or a proper chase and patch |
Need DStv installers in Hout Bay?
Tell us what you need or what your screen is showing. We give you a clear price before we drive out.
Mistake 5: fixings that rust in the sea air
Salt air in Hout Bay works its way indoors, especially in homes near Northshore and the harbour with doors open to the breeze. Zinc-plated screws and cheap brackets rust, and that rust bleeds down a white wall in brown streaks that never fully paint over.
On patios and covered stoeps it's worse, with wind off the Atlantic driving damp into every joint. We use coated brackets and stainless fixings for any screen near an outside door. The same salt does damage outside, which our post on signal problems from salt and wind explains.
Technician tip
A dab of clear sealant over exposed screw heads on a patio bracket slows rust a lot. Check outdoor mounts once a year and tighten anything that's worked loose in the wind.
Mistake 6: hacking a cable route into the plaster
Hidden cables look great when they're done properly. Done badly, a chase cut with the wrong tool leaves cracked plaster along its whole length, and the crack comes back after every patch.
For most homes, painted trunking is the gentler choice. Where cables must go inside brick, the groove needs to be cut cleanly, the cable laid in conduit and the wall replastered. If the decoder or router is moving too, our decoder relocation team can plan the route in one go.
Mistake 7: the wrong TV mount screws on the screen side
Walls aren't the only thing that gets damaged. A screw that's too long can press into the back of the TV. One that's too short grips a few threads and lets the screen tilt off the bracket, taking a chunk of wall with it if it falls.
- Thread every screw in by hand first.
- Use spacers on curved backs so the bracket sits flat.
- Check the bracket locks have clicked before letting go of the TV.
Homes on slopes and holiday rentals
Houses on the steep slopes in Hughenden and Llandudno often have retaining walls or rock behind the lounge. Drilling those needs the right bits and anchors, and sometimes a different wall altogether. Holiday rentals have their own risk: guests swing arms hard and lean on screens.
For rentals, a fixed bracket with good locks survives longest. If you also want the TV wired for the network, our WiFi and network installation covers that on the same visit.
Get TV wall mounting done right
Our TV bracket fitting service checks the wall, matches every fixing and leaves a clean finish.
We also handle DStv installation in Hout Bay, so TV wall mounting and installation of a decoder can happen together. Send a photo of the wall through our contact page and we'll quote first.
TV wall mounting: FAQs
Does TV wall mounting damage walls?
It leaves four to six small holes, which are easy to fill and paint when the TV comes down. Real damage comes from wrong fixings, heavy arms on drywall, redrilling after a guessed height or rusting screws. Done properly, the wall stays sound.
Can TV wall mounting work on drywall?
Yes, if the bracket is bolted into the studs or a backing board fixed between them. Light screens can use rated cavity anchors. Heavy screens on full motion arms should not hang on the board alone, because it can tear.
How do I fix holes after removing a TV mount?
Clean out loose dust, fill each hole with a good filler, let it dry, sand it flat and paint. Bigger torn areas in drywall may need a patch. Rust stains need a stain-blocking primer before paint, or they show through.
Why do TV brackets rust in Hout Bay homes?
Salt air from the Atlantic gets indoors, especially near open doors and on patios. Zinc-plated screws and cheap steel rust quickly in it. Stainless fixings and coated brackets last much longer by the sea.
Can I mount a TV without studs?
On brick or concrete, yes, because the wall itself holds the plugs. On drywall without studs in the right place, use rated cavity anchors for light screens or add a timber backing board for heavier ones.
Talk to our Hout Bay team
Call or WhatsApp us for a quote. We answer quickly and we always price the job before we arrive.